Standard Collocation Aluminum Profiles for building interior 6063
T5 White Powder Coated Surface
Processing Method of Aluminum Frame Material
In the material of doors and windows, the material connected with
the wall. Its main feature is that the surface of the joint with
the wall is mostly flat, fixed on the wall, and cannot be moved.
Materials that can be opened in doors and windows. It is
characterized by the ability to move
The rectangle composed of frame material is divided into several
small rectangular materials.
Zhenzhongting: fixed on the frame material;
False middle support: fixed on fan material
On one side of the room, the profile used to fix the glass.
Round pressing line: suitable for 45 degree splicing
Square pressing line: suitable for 90 degree splicing
1. Good heat preservation
K value -- heat transfer coefficient
Common aluminum alloy k = 207 w / (m2k)
Broken bridge aluminum alloy k = 2 ~ 4 w / (m2k)
2. Sound insulation is good
Careful structural design and tight joints. Tested
3. Good air tightness
4. Good water tightness
5. Wind pressure resistance
The decorative surfaces on both sides are aluminum alloy with good
wind resistance, and the finished products of doors and windows can
reach grade 7
6. Fire resistance
Aluminum alloy is made of metal material and does not burn. Nylon
66 in the middle is flame retardant and does not burn. It is a
recognized flame retardant material
Broken bridge aluminum alloy doors and windows, equipped with
excellent hardware, make thieves helpless.
Powder Coated Types:
1: Air spraying method. The powder coating is placed in the spray
gun, and the coating is adsorbed on the surface of preheated
aluminum profile by the adsorption force of compressed air. The
powder is melted on the surface of aluminum profile. Thermoplastic
and thermosetting powder can be used. If it is thermosetting
powder, it should be solidified in the oven. This spraying method
is suitable for the surface of small aluminum profile.
2: Fluidized bed dip coating method. The aluminum profile is
preheated first, and then immersed in a powder coating fluidized
bed to melt the powder to the surface of the aluminum profile.
Thermoplastic and thermosetting powder can be used. If it is
thermosetting powder, it should also be solidified in the oven.
This spraying method is suitable for small aluminum profile surface
with thick film, as well as medium-sized pipes or metal mesh, which
can be fully dip coated.
3: Electrostatic powder spraying. This is a widely used powder
spraying method at present. It uses the principle of electrostatic
adsorption, so that the powder coating under electrostatic
induction can be adsorbed on the surface of aluminum profiles with
opposite charges. Both hot spraying and cold spraying can be used.
After spraying, it needs to be dried in the baking oven. This
spraying method is suitable for the surface of aluminum profiles
with different sizes and shapes, and uses thermoplastic and
thermosetting powders Fine.
4: Electrostatic fluidized bed dip coating method. This spraying
method combines the fluidized bed dip coating method and
electrostatic powder spraying method, using thermoplastic and
thermosetting powder, which is suitable for the mass production of
small aluminum profiles with film thickness less than 150 μ M.
5: Electric field corona coating method. The thermoplastic or
thermosetting powder is placed between two parallel electrodes to
make the powder coating charged, and the coating material is passed
through between the electrodes to make its surface absorb the
powder. A fluidized bed is placed under the device, and the
spraying material is sprayed from the nozzle of the ejector, which
is suitable for spraying small aluminum profiles with thin coating
(10-20 μ m).
What is aluminum door profiles:
1: According to the door opening mode: push pull aluminum alloy
door, flat open aluminum alloy door, folding aluminum alloy door.
2: According to the type of outer door frame: ordinary single outer
frame aluminum door, single wall aluminum door, full frame wall
3: According to the width of aluminum: 46 series, 50 series, 65
series, 70 series, 80 series, 85 series, 90 series, 93 series, 99
series and other aluminum alloy doors.
1. The material is light
2. Good sealing
3. Beautiful color
4. Convenient processing
Aluminum alloy profiles have the characteristics of high strength,
strong corrosion resistance and not easy to deformation. Why do
some aluminum alloy doors have gone shape before they are used for
a year? After analysis, under normal use, the deformation of
aluminum alloy door may be caused by the thickness of aluminum
alloy profile used. It is understood that the aluminum alloy indoor
door, which is available for consumers to choose in the building
materials market, has a variety of thickness of 0.8mm, 1.0mm and
1.2mm. The strength of aluminum alloy doors with thickness of more
than 1.0mm is better, and will not deform in 5-8 years under the
condition of normal use. But some small manufacturers cut materials
to reduce production cost, and even made bathroom doors with
aluminum alloy profiles with thickness of only 0.6mm. Because of
the thickness of the material, the aluminum alloy doors are easy to
Caution: the thickness of profile directly determines the quality
of aluminum alloy door. When consumers choose aluminum alloy doors,
do not greedy for cheap and choose aluminum alloy doors with too
|Description||Standard Collocation Aluminum Profiles for building interior 6063
T5 White Powder Coated Surface|
|Material Thickness(t)||0.8-2.0 mm|
|Materiral||aluminum alloy 6063|
|Color||Wood, Silver White ,Bronze , Champagne, Black, (RAL series)etc.|
|Surface Treatment||anodized, powder coated, electrophoresis, wood grain, polished and
|Shape||Square, Round, Flat, Oval, and according to customer's drawing.|
|Length||Normal length=6m or in customer's order|
|Usage||Building, Production Line, Decoration, Industrial, Transportation,
Door and window, etc.|
|Package||1. Pearl cotton foam for each profile;|
2. Wrap with shrink film exterior;
3. Packed according to customer request.
|Advantages/Features||Providing colorful products with various mechanical|
performances to adapt all kinds of architectural styles
Aluminum Door Frame Description
Interior: Non Finger-Jointed Pine or finger-jointed core with non
finger-jointed Pine veneer; optional non finger-jointed Douglas Fir
or finger-jointed core with non finger-jointed Douglas Fir veneer;
optional non finger-jointed White Oak or finger-jointed with non
finger-jointed Oak veneer; non finger-jointed Cherry or
finger-jointed core with Cherry veneer; non finger-jointed Mahogany
or finger-jointed core with non finger-jointed Mahogany veneer; non
finger-jointed Vertical Grain Douglas Fir or finger-jointed with
non finger-jointed Vertical Grain Douglas Fir veneer.
Kiln-dried to moisture content no greater than twelve (12) percent
at the time of fabrication
Water repellant preservative treated in accordance with WDMA I.S.4.
Frame exterior aluminum clad with 0.050 inch (1.3mm) thick extruded
Frame thickness: 1 3/16” (30mm)
Frame depth for full frame units have an overall 5 21/32” jamb
(144mm). 4 9/16” (116mm) jamb depth from the nailing fin plane to
the interior face of the frame for new construction
Frame depth for replacement frame units have an overall 3 ¼” jamb
(83mm) for replacement application and 2 3/16” (56mm) jamb depth
from the nailing fin plane to the interior face of the frame for
Frame bevel: Standard is no bevel, optional available are 8 degree
and 14 degree bevel (replacement frame only)